Suggested tools for wiper blades on a 2018-2022 Honda Accord
Easy · Estimated: 10-15 minutes · AI draft generated 2026-09-14
This AI-generated draft has not been independently verified for your vehicle. Confirm engine, trim, build date, tool fitment and torque specifications against the relevant service information before buying tools or starting work.
Tools to check first
26 in and 20 in J-hook beam blades
Microfiber towel to protect glass
Small flat-blade screwdriver or trim tool
14 mm socket, 3/8 in drive (arm removal only)
On the 10th-gen Accord the wiper arms park low, tucked under the rear edge of the hood, so the blades physically can't swing up off the glass until you move them. The easy fix is to turn the ignition on, flick the wipers, and shut the ignition off mid-sweep — the arms freeze partway up the windshield where there's plenty of room. From there it's a 5-minute J-hook swap with no tools.
Sizes are 26 inches on the driver side and 20 inches on the passenger side across 1.5T, 2.0T and Hybrid. The mistake people make is buying two of the same length, or letting the bare arm snap back against the glass while fumbling with the new blade — that's how you end up paying for a windshield instead of a $40 pair of blades. Lay a towel down first.
Research nearby retailers. Compare store locations and public product information. Confirm fitment, price and local stock with the retailer before traveling.Research stores free
Suggested tool and parts checklist
Item
Type
Product search
Replacement wiper blades 26 in driver / 20 in passenger, J-hook (9x3) mount Correct 10th-gen Accord sizes; mismatched lengths will collide or leave streaks.
Blade sizes and the J-hook mount are identical across the 1.5T, 2.0T and Hybrid, and across all trims. The only trim difference is rain-sensing wipers on EX-L and Touring, which use a sensor behind the mirror and need no calibration after a blade change.
Torque values to verify
Wiper arm-to-pivot nut (14 mm)
verify in the service manual
Blade-to-arm J-hook clip
No torque — snap-fit, must click and resist a firm tug
AI-generated procedure overview
Turn the ignition to ON (engine off is fine, press START/STOP once without your foot on the brake on push-button cars). Flick the wiper stalk on, then switch the ignition off while the blades are partway up the glass — they will stop mid-sweep clear of the hood lip. Alternatively, in a cold car just lift each arm; but if it won't clear the cowl, use the mid-sweep trick.
Lift the driver-side arm away from the glass until the hinge locks in the upright position, and lay a folded microfiber towel on the windshield under it.
Rotate the blade so it sits roughly 90 degrees to the arm to expose the J-hook clip.
Press the release tab on the blade's connector (a small screwdriver helps if it's tight) and slide the blade down and out of the hook.
Hook the new 26 in blade onto the arm, pull it up through the J-hook until the tab clicks, then tug firmly to confirm it is locked.
Lower the arm gently onto the glass — never let a bare arm spring back.
Repeat on the passenger side with the 20 in blade.
Clean the windshield wipe path with glass cleaner and wipe the new blade rubber with a damp cloth to remove packing residue.
Turn the ignition on, run the washers and wipers through several sweeps, and check for chatter, streaks, or the blades hitting each other or the A-pillar trim.
Turn the ignition off with the wipers switched off so the arms return to their parked position under the hood lip.
Watch out
Never let a wiper arm slap down without a blade on it — it will chip or crack the windshield. Keep a towel on the glass.
Don't force the arms up against the hood lip. If they won't clear, use the mid-sweep stop method rather than bending the arm.
Confirm the clip has clicked. A blade that detaches at highway speed will gouge the glass.
Avoid ammonia-based household cleaners on the glass near the rain sensor gel pad and interior trim.
On rain-sensing trims, leave the wiper switch in AUTO off while working, or the wipers may sweep unexpectedly when the ignition is on.
Frequently asked
What size wiper blades fit a 2018-2022 Honda Accord?
26 inches on the driver side and 20 inches on the passenger side. Both arms use a standard J-hook (9x3) connector, so most beam-style aftermarket blades fit without an adapter.
How do I get the wiper arms to lift off the glass on my Accord?
They park under the hood lip. Turn the ignition on, switch the wipers on, then turn the ignition off while the blades are partway up the windshield — they stop there and the hinges will then lock upright.
Do I need any tools to change Accord wiper blades?
Not really. A folded microfiber towel to protect the glass and a small flat screwdriver to press a tight release tab are all that help. A 14 mm socket is only needed if you're removing a wiper arm from its pivot.
Why do my new wipers chatter or streak on my Accord?
Usually a dirty or waxed windshield, or packing oil left on the new rubber. Clean the wipe path with glass cleaner and wipe the blade edge with a damp cloth. Persistent chatter on one side can mean a bent arm or worn pivot bushing.